Mobile Phone Repairing Testing Methods
Faults in each part, component or section of a mobile cell phone can be repaired fast by using following 2 methods at the time of repairing mobile cell phone. These methods can also be used to find out...
Faults in each part, component or section of a mobile cell phone can be repaired fast by using following 2 methods at the time of repairing mobile cell phone. These methods can also be used to find out faulty or damaged parts or components inside a mobile cell phone.
- Cold Testing Method: When we check the value of resistance using a multimeter at the time of repairing a fault in any mobile phone, it is called cold testing. There is no need to give any power supply to the faulty mobile phone from any equipment such as DC Power Supply or battery during cold testing. Diode Range and Beep Sound from the multimeter is used to find fault in a mobile cell phone using the cold testing method of mobile phone repairing. In this testing method, the RED Probe of the multimeter is connected to the ground of the mobile phone PCB and the BLACK Probe is touched at the testing points of the mobile phone. During the fault finding and repairing process of each part, component or section, following correct values will be received:
- Ear Phone Connector Tip (+ , -): .500 to .700
- Loud Speaker / Ringer Connector Tip (+,-): .300 to .600
- Battery Connector Tip (+): .400 to .500
- Battery Connector Tip (Sense): above .800
- Display Connector Supply Pins: .250 to .400
- Display Connector Signal Pins: .500 to .800
- Camera Connector Supply Pins: .250 to .400
- Camera Connector Signal Pins: .600 to .900
- Key Tip (Row and Column): .400 to .800
- Charger Connector Tip: .600 to .700
- Vibrator Motor Connector: .40 to .500
- Power ON / OFF Switch Point (+): .600 to .900
- MIC Connector Tip (Analog MIC) (+,-): .700 to .900
- Battery Charging Out Point (+,-): .300 to .400
- SIM Card Connector Pin 1 (VSim): .500 to .700
- SIM Card Connector Pin 2,3,6: .400 to .800
- SIM Card Connector Pin 4 (GND): .00 (Beep)
- Micro SD Card Connector Pin 4: .500 to .600
- Micro Card Connector Pin 6 (GND): .00 (Beep)
- Micro Card Connector Pin 1,2,3,5,7,8: .600 to .800
- RTC: .400 to .500
- Data RX and TX Pins: .600 to .700
- Hot Testing: This is the second method of fault finding and repairing any mobile cell phone. Hot testing method of mobile phone repairing is adopted when the fault cannot be found or when the phone cannot be repaired using the Cold Testing Method. In this method, VOLTAGE of damaged part, component or section of a mobile phone is checked. The fault is found by giving Power Supply to the mobile phone with a Battery of DC Power Supply Equipment such as DC Power Supply. In this method, DCV (DC Volt) range of the Multimeter is selected. The BLACK Probe of the multimeter is connected with the Ground of the Mobile Phone PCB and the RED Probe is touched at the Testing Points. During Hot Testing method, Voltage of different part or sections should be as follows (All Values in Volt):
- Ear Phone Connector Tip (+ , -) during working: .0 to 2.5
- Loud Speaker / Ringer Connector Tip (+,-) during working: .0 to 2.5
- Battery Connector Tip (+): 3.7
- Display Connector Supply Pins: 1.8 to 2.9
- Display Connector Signal Pins During Working: .0 to 1.8
- Camera Connector Supply Pins: 1.8 to 2.9
- Camera Connector Signal Pins During Working: .0 to 1.8
- Key Tip (Row and Column) One Side: 1.8 to 2.8
- Charger Connector Tip: 5 to 6
- Vibrator Motor Connector Tip During Working: 1.9 to 3.6
- Power ON / OFF Switch Point (+): 3 to 3.6
- MIC Connector Tip (Analog MIC) (+,-): 1.8 to 3.0
- Battery Charging Out Point (+,-): 3.7 to 4.2
- SIM Card Connector Pin 1 (VSim) When SIM Connected: 1.8 to 3.0
- SIM Card Connector Pin 2,3,6 During Working: 0 to 2.8
- Micro SD Card Connector Pin: 2.8
- Micro Card Connector Pin 1,2,3,5,7,8: 0 to 2.8
- Data RX and TX Pins: 1.8 to 2.8
Related Posts:
- How to Open and Disassemble a Mobile Cell Phone
- Smartphone Repairing
- Mobile Phone Ringer Problem and Solution – How to Solve Ringer Fault in any Mobile Cell Phone
- Mobile Phone Vibrator Problem and Solution – How to Solve Vibrator Fault in any Mobile Cell Phone
- Mobile Phone Light LED Problem and Solution – How to Solve Light or LED Fault in any Mobile Cell Phone
- Mobile Cell Phone Earpiece / Ear Speaker Problem and Solution – How to Solve Light or LED Fault in any Mobile Cell Phone
- Mobile Cell Phone Microphone / Mic Not Working Problem and Solution – How to Solve Microphone Fault in any Mobile Cell Phone
- Mobile Cell Phone Keypad Not Working Problem and Solution – How to Solve Keypad Fault in any Mobile Cell Phone
- Mobile Cell Phone Screen Touch (PDA) Not Working Problem and Solution – How to Solve Screen Touch (PDA) Fault in any Mobile Cell Phone
- Mobile Cell Phone Display Not Working Problem and Solution – How to Solve Display Fault in any Mobile Cell Phone
- How to Reset Samsung Mobile Phone
- How to Reset LG Mobile Phone (GSM)
- How To Reset Motorola Mobile Phone
- MTS Mobile Phone Insert Room Card Problem and Solution
- How to Reset Nokia Mobile Phone
- How to Check Mobile Cell Phone Settings
- How to Jumper in Mobile Phone Repairing
- How to Clean Points and Connectors of Mobile Phone PCB
- How to Check Parts of a Mobile Phone for Fault
- How to Replace LCD Display Screen of a Mobile Cell Phone
- Parts Inside Apple iPhone 5 Mobile Phone
- Mobile Phone and Communication Technology – Technology is Cell Phones
- Top Mobile Cell Phone Manufacturers in the world – Best Leading Mobile Cell Phone Manufacturers
Hi sir,
I have a question i have mmx canvas knight 2 which is not turning on and doesn’t shows the charging logo when i charge and even the red blinker above is not blinking i used a custom rom and it was working good but after i updated the rom version it went to recovery mode and then suddenly it shutted down
Could be shorting somewhere.
Please can u explain the different testpoints and how to use them?
I have already explained how to use a multimeter and how to test components for fault. Please go through my articles.
Wowww thank u so much sir that article has been of great help
Thank you sir! Please i have a major problem with one viwa T3 the vbat has automatically changed to ground when checked with a multimeter while the negative side of the battery connector will not beep if Checked with a multilmetre but if you put your test probe on the vbat and ground line it will beep please help me how do i go about it i am confused. Thank you for your time understanding i await your swift response.
You have to check the Tracks of viwa T3 Properly. Now a Days the Circuit are changing in different Phone Models but the Basic Rule of Electricity is Same.
Thank you sir! I will contact you if i have further questions. May our Goog God continue to bless and strengthen you for the knowledge you are impacting on us.
hello sir
what does mean battery connector tip (sense) means?
thanks for making website to give us free knowledge.
The three Copper Points where the Battery Connects is called Battery Connector.
Please sir! I tried practicing everything but i am getting different values how do i go about it? Or the multi-metre are they not the same?
Use a different multi meter and check.
this site greatly helpful. thanks Santosh Das
how do you determine the “ground” on a pcb? thanks
Ground is basically on the Copper Tracks.
Thanks for the reply. I was doing that but was not sure i was doing the right thing. i discovered your site about 3 weeks ago. But what i have learnt here is much appreciated
awesome technical knowledge …thank you :)…
thanks a lot…
ok this i know but when is damage a cpu how measure then ???
I get many knowledge from your post. very thanks.If want to give anything I want many type of cell layout diagram with label.
this is the superb and exellent effort by sh.santosh das g!!!
which is incomparable ……
Please how can i get all this information on cd.help cos i’m a mobile phone technician who wants to improve my knowledge.what about software and flashing of fones.